Exhaust Manifold Bolt Size Chart for Common Engines

Exhaust Manifold Bolt Size Chart for Common Engines

Common exhaust manifold bolts include M8x1.25, M10x1.5, and 5/16-18, but thread, length, and flange style still need to match the exact engine before buying. The wrong bolt can strip threads, crack the manifold, or leave a leak that wastes time and money. This guide gives an engine-by-engine bolt size chart, plus quick checks for thread pitch, shank length, and whether your fasteners are studs, bolts, or flanged bolts.

Exhaust manifold bolt basics

Key points: Exhaust manifold bolt basics
Recommended gear
Our pickVoxnopy 10 PCS M8 x 1.25 Exhaust Manifold Bolt Kit, M8 Hex Flange Bolts with Nuts, High Strength Carbon Steel Anti-Rust

Voxnopy 10 PCS M8 x 1.25 Exhaust Manifold Bolt Kit –⁠ $8.99

Voxnopy · M8 x 1.25 · 10 pcs · hex flange
$8.99
Price as of 21 Nov 2026
Drawback: M8 only; confirm your exact thread and fit

View on Amazon →

Also greatwipcowi 2 PCS Car Exhaust Manifold Bolts, M10 x 1.5 Vibration-damping Fastening Flange Bolt and Nut with Spring, Alloy R

wipcowi 2 PCS Car Exhaust Manifold Bolts –⁠ $6.25

wipcowi · M10 x 1.5 · 2 pcs · spring flange
$6.25
Price as of 21 Nov 2026
Drawback: Only 2 pieces; confirm M10 x 1.5 fit

View on Amazon →

Budget pickBawkars 5 PCS M12-1.75X30mm Exhaust Manifold Bolts, 10.9 Grade Hexagon Flanged Head Bolt Hardware Kit, Non-Slip Hex Flan

Bawkars 5 PCS M12-1.75X30mm Exhaust Manifold Bolts –⁠ $15.89

Bawkars · M12-1.75 x 30mm · 5 pcs · flanged
$15.89
Price as of 21 Nov 2026
Drawback: M12-1.75 x 30mm only; check fit first

View on Amazon →

As an Amazon Associate we earn from qualifying purchases. Prices and availability are accurate as of the date shown and are subject to change.

An exhaust manifold bolt is more than a metric or SAE thread callout. You need the thread diameter, pitch, under-head length, head style, material grade, coating or finish, and whether the part is meant to be reused or replaced during service.

Thread diameter, pitch, and length

Thread diameter tells you the nominal bolt size, such as M8 or M10. Pitch tells you the distance between threads, such as 1.25 mm or 1.5 mm. Length is the usable bolt length under the head, and it matters because a bolt that is too short may not clamp fully while a bolt that is too long can bottom out before the gasket or manifold seats.

Head style, washer use, and coating

Head style affects tool access and clamp load. Common examples include hex head bolts and flanged bolts; some hardware kits also use flat washers or ramp-lock washers to help maintain clamp load under heat cycling. Coatings vary by listing, but black galvanized and other high-temperature finishes are common on replacement hardware.

Reuse versus replacement

Reuse only if the bolt threads are clean, the shank is straight, the head is not rounded, and the bolt has not stretched or corroded. Replace seized, pitted, necked-down, or damaged bolts. On exhaust hardware, a bolt that threads in is not automatically the right bolt if the head, washer stack, or length is wrong.

Common exhaust manifold bolt chart

This chart helps you separate a true fitment match from a bolt that only looks close. Use the engine family row that matches your application, then confirm the exact manifold, head casting, and hardware package before ordering.

Engine familyBolt thread sizePitchNominal lengthHead styleWasher useOne-piece or kit notes
GM LS1 / LS2 / LS3 / LSX / LT seriesM81.2525 mm exampleHexagon headCheck listing; kit may use washersOne example is a 12-bolt package in Grade 10.9 steel with black galvanized finish and right-hand fine thread, thread class 2A
Ford 428 Cobra Jet, 1968-1970 passenger-side manifoldCheck the manifold and service listingCheck the service listingVaries by casting and spacer useCheck the hardware listingOriginal installation was without a gasketRegistry references C8OE-9428-A and C8OE-9430-B; verify engineering number and spacer/no-spacer layout before ordering
Other exhaust manifold applications with spring hardwareM101.5Check the listing for your modelCheck the listing for your modelSpring hardware may be part of the kitOne listing uses springs for vibration absorption and describes high-temperature resistant manganese and 45 gauge steel

That chart is intentionally narrow. It does not claim every LS, LT, Ford, or diesel engine uses the same bolt length or washer stack. Length can change with manifold thickness, header flange thickness, spacer plates, and casting depth.

How do you identify the right bolt?

Match the bolt by measurement first, not by appearance. A fastener that fits the hole can still be wrong if the pitch, head style, washer seat, or length does not match the original hardware and manifold stack.

  1. Measure the diameter.
    Use a caliper on the threaded section, not the head. Confirm whether the bolt is M8, M10, or a fractional size such as 5/16 before you compare it to catalog listings.
  2. Check the pitch.
    Use a thread gauge or compare against a known sample. M8x1.25 and M10x1.5 are both common exhaust hardware patterns, but they do not interchange.
  3. Measure under-head length.
    Measure from the underside of the head to the end of the bolt. This matters because a bolt that is too long can interfere with the hole depth, while a bolt that is too short may not clamp the flange fully.
  4. Confirm head and washer style.
    Identify whether the bolt uses a hex head, flange head, flat washer, or spring-style hardware. Match the washer depth and seat style so the clamp load is spread correctly across the manifold ear or flange.
  5. Verify the mounting pattern.
    Count the holes, note bolt spacing, and compare the casting or flange shape to the engine family. If the pattern does not match, the bolt may be the wrong application even if the thread fits.

Say your LS manifold uses an M8 thread, but the replacement header flange is thicker than stock. The thread can still be correct while the 25 mm length no longer clamps properly, so you need the longer application-specific bolt rather than the first M8 bolt that fits the hole.

A common first-timer mistake is buying bolts by head style alone. A hex head M8 bolt can look right on the bench and still be wrong if the pitch is off by a step or the washer stack does not match the manifold seat.

Exhaust manifold bolts for LS and LT engines

For the GM LS and LT family, one documented hardware example uses M8-1.25 x 25 mm bolts and is described as fitting GM LS1, LS3, LS2, LSX, and LT series engines. That example is a 12-bolt package, uses Grade 10.9 steel, has a black galvanized finish, a hexagon head style, right-hand fine thread, and a thread class of 2A.

Key points: Exhaust manifold bolts for LS and LT engines

LS1, LS2, LS3, and LSX notes

The key point for these engines is not just thread size. The listed example is a fitment reference, not a universal promise that every LS or LT exhaust manifold uses the same length, head style, or washer stack. LS7, thicker headers, and some aftermarket manifolds may need different hardware, so check the manufacturer’s listing for your model.

1997-up fitment and the M8-1.25 x 25 mm example

The 1997-up LS example is the safest starting point for stock-style manifold replacements on the listed family. Use it as a match only when the engine family, manifold thickness, and bolt count line up with the listing. If the part description does not name your exact engine or manifold, confirm before buying.

When thicker manifolds or headers change length needs

Thicker aftermarket flanges, spacer plates, or repair inserts can change the under-head length you need. That is why a bolt can be the right diameter and pitch but still be wrong for clamp load. If the catalog does not state the thickness assumption, check the manufacturer’s listing for your model.

Ford 428 Cobra Jet manifold hardware

For the Ford 428 Cobra Jet, the registry notes a 1968-1970 cast-iron manifold application and says the original installation was without gaskets. The early passenger-side manifold engineering numbers listed are C8OE-9428-A and C8OE-9430-B, so you should match the casting and service part information before assuming any bolt or spacer stack is correct.

1968-1970 application notes

This is a good example of why “Ford exhaust bolt” is too broad to be useful. The 428 Cobra Jet manifold hardware depends on the exact year range, the side of the engine, and whether a spacer is present. A bolt that works with one casting may not seat correctly on another.

Engineering numbers and service part numbers

Use the casting and service part data together when you shop. The registry’s engineering numbers help identify the manifold itself, but the correct bolt or spacer can still vary with service replacement parts. If your part number does not match the original casting family, confirm the hardware separately.

Spacer use, no-spacer use, and original sealing

Some Cobra Jet installations use spacers, while others do not. That changes the required under-head length and may change washer choice as well. Because the original installation was without gaskets, do not add a gasket unless the replacement manifold or service instructions call for one.

Exhaust manifold hardware kit chart

A hardware kit is often easier than piecing together loose bolts, washers, and springs one by one. The right kit should match the engine family, bolt count, washer types, and any spring or ramp-lock hardware the application needs.

Kit typeBolt countWasher typesHardware detailBest use case
LS / LT manifold kit example12-bolt packageCheck listingM8-1.25 x 25 mm, hex head, Grade 10.9, black galvanized, right-hand fine thread, 2AStock-style GM LS1, LS2, LS3, LSX, and LT manifold replacement when the listing matches your engine
Spring-assisted exhaust kit exampleCheck the listing for your modelSpring hardware and possible flat washersM10x1.5 mm threads, springs for vibration absorption, high-temperature resistant manganese and 45 gauge steelApplications that call for spring loading or a kit with added vibration control

Use flat washers when the manifold seat needs a broad bearing surface. Use ramp-lock washers only when the application calls for them, because washer shape affects clamp behavior. A complete kit makes more sense when the listing matches your engine exactly and includes the bolt count, washer type, and any spring hardware in one box.

Exhaust manifold gasket fitment

An exhaust manifold gasket can add leak protection when the engine and manifold design call for it, especially after a repair that needs a renewed sealing surface. It must match the specific engine or manifold, because a gasket can fix one fitment problem and create another if the port shape or bolt pattern is wrong.

Use a gasket only when the application supports it and the mating surfaces are clean, flat, and undamaged. On cast-iron hardware that was originally run without a gasket, adding one without checking compatibility can change clamp load and port alignment.

Keep reading

Frequently asked questions

What size are exhaust manifold bolts on my engine?

The most common answers are M8x1.25, M10x1.5, or 5/16-18, but the correct size depends on the exact engine, manifold, and year. Match diameter, pitch, length, and head style before buying. A bolt that fits the hole can still be the wrong hardware for sealing and clamp load.

Are exhaust manifold bolts M8 or M10?

They can be either, and both sizes are common across different engine families. GM LS and LT examples often use M8-1.25, while some other applications use M10x1.5. Check the engine family and the catalog listing instead of assuming one size fits all.

How do I match exhaust manifold bolts to a specific engine?

Start with the engine family, then confirm the manifold casting or part number, bolt count, thread diameter, pitch, and under-head length. Next, match the head style and washer stack. If any part of the listing is vague, check the manufacturer’s listing for your model before ordering.

What thread pitch do exhaust manifold bolts use?

Thread pitch varies by application. M8-1.25 and M10x1.5 are both common exhaust-related patterns, but they do not interchange. Use a thread gauge or compare against known hardware, then confirm the result against the engine family and manifold listing.

Do exhaust manifold bolts differ between LS and Ford engines?

Yes. The GM LS and LT example cited here uses M8-1.25 x 25 mm bolts, while the Ford 428 Cobra Jet example requires year-specific and casting-specific verification, including spacer use and original no-gasket sealing. Do not move parts between those engines without checking the exact application.

Can I reuse exhaust manifold bolts?

Reuse only if the bolt is straight, the threads are clean, and there is no rounding, stretching, or heavy corrosion. Replace seized or damaged hardware. Exhaust fasteners live in high heat and vibration, so worn bolts can lose clamp load and contribute to leaks even if they still thread in.

What hardware kit do I need for exhaust manifold replacement?

Choose a kit that matches the exact engine and manifold, then confirm bolt count, washer type, and any spring or ramp-lock hardware. A complete kit is easier than sourcing loose pieces, but only if the listing matches your application. For LS family examples, the cited kit is a 12-bolt package.

How do I identify the correct manifold bolt pattern?

Count the holes, compare the spacing, and check whether the flange or casting uses spacers, studs, or a gasketed layout. Then compare the pattern to the engine family and casting number. If the manifold pattern does not match the hardware listing, do not force it to fit just because the threads start.

Similar Posts