6.7 Cummins Exhaust Sensor Locations
The 6.7 Cummins exhaust sensor is located on the drivers side of the engine, just above the turbocharger. It is a small black sensor with two wires coming from it.
If you’re looking for the exhaust sensor on your 6.7 Cummins, there are a few different places it could be located. The most common location is right before the catalytic converter, but it can also be located after the turbocharger or in the downpipe. It’s important to know where your exhaust sensor is located so you can properly diagnose any issues that may come up.
Dodge Ram 6.7 Cummins diesel P0471 exhaust pressure sensor
6.7 Cummins Exhaust Pressure Sensor Location
If you’re looking for the 6.7 Cummins exhaust pressure sensor location, it’s actually pretty easy to find. It’s located on the driver’s side of the engine, just behind the fuel filter. You’ll need a 3/8″ ratchet and a 6″ extension to reach it.
6.7 Cummins Exhaust Pressure Sensor Delete
If you’re looking to delete your 6.7 Cummins Exhaust Pressure Sensor, there are a few things you need to know. First, the sensor is located on the exhaust side of the turbocharger, so you’ll need to remove the turbo in order to get to it. Second, there are two types of sensors – one for early model trucks and one for late model trucks.
Make sure you know which type you have before ordering a delete kit.
Once you have the correct delete kit, installation is relatively straightforward. However, keep in mind that deleting your exhaust pressure sensor will trigger a check engine light – so be prepared to deal with that if necessary.
6.7 Cummins Exhaust Pressure Sensor Symptoms
If your 6.7 Cummins is experiencing any of the following symptoms, it may be time to replace the exhaust pressure sensor:
1. Check Engine Light is on
One of the first and most common signs that your 6.7 Cummins’ exhaust pressure sensor needs to be replaced is if the check engine light comes on.
If you have a code reader, you can check for specific error codes that will point to this particular sensor.
2. Poor Fuel Economy
Another symptom of a faulty exhaust pressure sensor is decreased fuel economy.
Because the sensor helps to regulate how much fuel is injected into the engine, if it’s not working properly, too much or too little fuel could be flowing through – both of which would lead to poorer mileage.
3. Exhaust Brake Not Working Properly
If you have an exhaust brake on your 6.7 Cummins and it’s not working as well as it used to, that could also be a sign that the pressure sensor needs replacing.
The sensor helps to control when the brake engages, so if it’s not functioning correctly, neither will the brake itself.
6.7 Cummins Exhaust Pressure Sensor Reading
If your 6.7 Cummins is anything like mine, then you’re always looking for ways to get a little more power out of it. One way to do that is by installing an aftermarket exhaust pressure sensor.
An exhaust pressure sensor can help you monitor and adjust the amount of exhaust backpressure in your system.
This can be a great way to improve performance and fuel economy.
Installing an aftermarket sensor is relatively simple and can be done in about an hour. Here’s what you’ll need:
-Exhaust pressure sensor (I recommend the S&B Particle Separator)
-T-fitting (for the sensor installation)
-Exhaust pipe sealant (I used Permatex High Temp RTV Silicone Gasket Maker)
-Wire tap connectors (for connecting the sensor wire to your factory wiring harness)
Credit: hdrams.com
Where is the Exhaust Pressure Sensor on a 6.7 Cummins?
The exhaust pressure sensor is located on the exhaust side of the turbocharger, near the outlet flange. It is used to measure the pressure in the exhaust system and send a signal to the engine control unit (ECU). The ECU uses this information to adjust the fuel injection and timing.
Where is the Exhaust Gas Pressure Sensor on a Cummins?
The exhaust gas pressure sensor on a Cummins is located at the back of the engine, near the exhaust manifold. It is typically mounted in a metal housing with two wires running to it. The sensor itself is a small device that measures the pressure of the exhaust gases as they flow through the manifold.
Where is the Exhaust Gas Pressure Sensor Located?
The exhaust gas pressure sensor is located in the exhaust system, downstream of the catalytic converter. It measures the pressure of the exhaust gases and sends a signal to the engine control unit (ECU). The ECU uses this information to adjust the air/fuel mixture and ensure that the engine is operating at peak efficiency.
What is the Code for Exhaust Pressure Sensor on 6.7 Cummins?
If your truck is equipped with a 6.7L Cummins engine, the code for the exhaust pressure sensor is 5244060. This sensor is located on the exhaust manifold and monitors the pressure in the exhaust system. If the sensor detects an abnormal condition, it will send a signal to the engine control module (ECM) which will then illuminate the check engine light on the dash.
Conclusion
The 6.7 Cummins has two exhaust sensors, the upstream and downstream sensor. The upstream sensor is located before the catalytic converter and the downstream sensor is located after the catalytic converter. These sensors are used to monitor the exhaust gas temperature and make sure it is within safe limits.
If either of these sensors fail, it can cause engine damage or even a fire.
